G2086 Medicaid reimbursement rate by state (2026)

• Order. States are listed from the highest published rate to the lowest. No single unit is shared by 8 or more states for G2086, so the order is by published amount and is not a like-for-like rank.
• Medicaid rate. The most the state's fee-for-service program pays for one unit, as published. 9 of the 11 states list more than one rate for G2086, by modifier, provider type or setting; the table shows the one that matches the provider level and setting used across states, without add-ons.
• Unit. None of the 11 schedules prints a separate unit for G2086, so each amount is a flat payment for one service as the code defines it.
• Per hour. G2086 is not billed in time units in these states, so no hourly figure is shown.
• Managed-care plans. The rule the state sets for its plans on this rate. What each rule means is explained below.
• % of Medicare. Medicare amounts exist for G2086, but no state's Medicaid unit matches Medicare's billing unit closely enough to compute a percentage.
• Source and date. Each Source link opens the state's own document; “since” is the date the rate took effect.

Published rates for G2086 run from $181.31 in New Jersey to $690.59 in Montana, a 3.8x gap in the same unit. Half the states pay more than the median of $393.19 and half pay less. The usual reasons for a spread like this in physician & professional rates:

• Modifiers such as professional or technical component, bilateral, multiple procedure and assistant at surgery change the amount paid, and states apply them with their own percentages.
• Each state sets its own physician conversion factor or fee for every code, and many update them on a state budget cycle rather than on Medicare's calendar.
• Primary-care and pediatric add-ons, enhanced rates for certain specialties and targeted increases for access problems change individual codes without moving the rest of the schedule.

Timing matters too. 9 states set the current rate for G2086 in 2026 or later, while 1 state still pay a rate that took effect in 2022 or earlier. A state that has not updated its rate in years will drift down the ranking as others raise theirs.

Most Medicaid members are in managed-care plans, and plans don't publish their provider fee schedules. For G2086, the public signal is the rule each state sets for its plans, recorded on each rate above.

In 4 states, the published rate binds plans: a floor, a pass-through or a state-set rate. In 4 states, plans negotiate and the published rate is a benchmark or out-of-network default. In 1 state, the service is paid outside the plans or through a state-directed payment. The rule for the remaining 2 states is not classified yet.

• Plans must pay at least the published rate (4 states). The published rate is your floor. Negotiate up from it, and if a plan pays less, the contract provision is the basis for a payment dispute.
• Plans negotiate; the published rate applies out of network (4 states). In-network rates can be above or below the published rate. The published rate is the benchmark both sides know, and the fallback if no contract is signed.
• State-directed payment (1 state). Eligible providers receive the directed amount on top of, or as a floor under, negotiated rates. Check whether your provider class qualifies.

Plan-negotiated rates are never estimated here. To see the rule and its citation for a particular state, open that state's managed-care page, for example Montana managed care.

G2086 is a HCPCS Level II professional services code in the physician & professional line, billed mostly by physicians, nurse practitioners, physician assistants and other licensed practitioners. G codes describe professional services and procedures that have no CPT code, or that payers define more narrowly. Many are timed, so check the unit before comparing.

Practitioners who are not physicians are often paid a reduced percentage of the published amount, so check the schedule for the reduction that applies to your provider type. Physician-fee-schedule codes are billed per service: one unit is one occurrence unless the code itself is defined by time or quantity.

Medicare's 2026 physician fee schedule pays $459.32–$597.03 for G2086 (non-facility), depending on the Medicare locality. That is a useful reference point, but Medicare and Medicaid can define the unit differently, so compare only where the units match.

Before billing, confirm the rate, unit and any modifier with the state's current schedule or the plan: the amounts here are as published, not a guarantee of payment.